# PVsyst's forum

Welcome on PVsyst's forum.
 It is currently Thu Aug 06, 2020 12:07 am

 All times are UTC+02:00

 Post new topic  Reply to topic Page 1 of 1 [ 9 posts ]
 Print view Previous topic | Next topic
Author Message
 Post subject: Inverter LossesPostPosted: Wed Aug 15, 2012 9:57 pm

Joined: Wed Aug 15, 2012 9:55 pm
Posts: 1
Do you have more descriptive definitions of the particular inverter losses? I was looking in various PVsyst literature and was unable to find more in-depth definitions of the following losses:

InvLoss Global inverter loss
IL Oper Inverter Loss during operation (efficiency curve)
IL Pmin Inverter Loss due to power threshold'
IL Pmax Inverter Loss due to power overcharging
IL Vmin Inverter Loss due to low voltage MPP window
IL Vmax Inverter Loss due to upper voltage MPP window

Thank you.

Top
 Post subject: Re: Inverter LossesPostPosted: Sat Oct 20, 2012 10:41 am

Joined: Mon Apr 16, 2012 7:29 pm
Posts: 1658
InvLoss Global inverter loss
- This is the sum of all inverter losses.

IL Oper Inverter Loss during operation (efficiency curve)
- The inefficiency loss, computed according to the efficiency curve.

IL Pmin Inverter Loss due to power threshold'
- Loss when the power of the array is not sufficient for starting the inverter.

IL Pmax Inverter Loss due to power overcharging
- When the MPP power is over the input power required for obtaining the specified PNom(ac), the inverter displaces the operating point on the I/V curve in order to get exactly the required power for Pnom(ac). This IL Pmax loss value represents the difference between the Pmpp and this adjusted power.
NB: The displacement is towards higher voltages. If the voltage exceeds the Vmaxmpp limit of the inverter, the inverter has to stop, and the Pmpp is fully lost.

IL Vmin Inverter Loss due to low voltage MPP window
IL Vmax Inverter Loss due to upper voltage MPP window
- If the Vmpp is outside of the inverter's window (Vmppmin/VmppMax) the inverter will clip it to the limit value. This loss is the difference between Pmpp and the corresponding P of the I/V curve at the limit value.

Top
 Post subject: Re: Inverter LossesPostPosted: Thu Nov 01, 2012 4:15 am

Joined: Wed Oct 31, 2012 6:23 pm
Posts: 2
THank you for the reply. It was very helpful in evaluating the .csv file. I have evaluated several of the files and discovered that the inverter Pnom or nameplate max AC output is often surpassed on the output file. In this case, it was for 11% of the operating hours, with the total amount of time the inverter was clipping 27% of operating hours. When clipping was not occuring though it was supposed to, the inverter loss due to efficiency was negligible, and the inverter loss due to max power was 0. This made the inverter look very efficient on the output page.
Attachment:
File comment: The file doesn't stop at max power, but efficiency is right

clipping not working but efficiency right.png [ 28.56 KiB | Viewed 17169 times ]
On a different simulation however, the inverter clipped appropriately and the Pmax losses were correct, however now the inverter losses due to efficiency were relatively high vs. the previous simulation, where if the inverter was producing at max nameplate, the efficiency losses were zero, which makes sense. I would argue once the inverter is at nameplate, all the losses should be due to power threshold. Taking it one step past that, I would even argue as is seen in this screen shot below, that if the inverter is producing at 2kW below nameplate (in this case, 18 500kW inverters) or 7998, the max efficiency loss should be 2kW and the rest should go to power threshold.
Attachment:
File comment: clipping modeled correctly, but efficiency confusing

efficiency vs. clipping loss clipping correctly.png [ 17.98 KiB | Viewed 17169 times ]
Can you please explain why the difference and how that happens?

Thanks in advance. I am also Swiss, but from the German part living in the US. I hope to soon make it back for one of your trainings.

Last edited by cheinzer on Thu Nov 01, 2012 4:45 am, edited 1 time in total.

Top
 Post subject: Re: Inverter LossesPostPosted: Thu Nov 01, 2012 4:40 am

Joined: Wed Oct 31, 2012 6:23 pm
Posts: 2
I have also noticed that there are InvLoss when there is no power production, and it almost seems random. Any idea what may be causing this? I have attached a screen shot of my simulation output .csv to show this.

 Attachments: zero output efficiency loss.png [ 15.39 KiB | Viewed 17169 times ]
Top
 Post subject: Re: Inverter LossesPostPosted: Thu Nov 08, 2012 1:50 am

Joined: Mon Apr 16, 2012 7:29 pm
Posts: 1658
I don't have definitive answers. Which version are you using ?

Until version 5.57, there were an error in the simulation process: when the Vmpp was lower than VmppMin (il_VMin loss), the overpower was not checked.
This may have some effect in systems with low Vmpp value (by hot conditions).
Since 5.58, this has been corrected: The overpower increases the Voper value, and is comptabilised first. Usually this brings the Voper over the VmppMin value.

Now with highly oversized arrays and high Vmpp (more modules in series), you have the risk that the overpower correction leads to an operating voltage higher than VmppMax, and in this case the inverter has to stop completely (it cannot find a suitable operating point), leading to high overpower losses.

The losses at very low irradiance are quite normal, I don't see where is the problem.

Top
 Post subject: Re: Inverter LossesPostPosted: Thu Nov 15, 2012 10:15 pm

Joined: Thu Nov 15, 2012 9:56 pm
Posts: 1
A slightly different question, but could you please explain the following terms in the Loss diagram?
• Inverter Loss during operation (efficiency)
• Inverter Loss over nominal inv. power
• Inverter Loss due to power threshold
• Inverter Loss over nominal inv. voltage
• Inverter Loss due to voltage threshold
It's the second one ("Inverter Loss over nominal inv. power") that I'm having most trouble understanding.

thanks,
Stewart

Top
 Post subject: Re: Inverter LossesPostPosted: Thu Nov 22, 2012 1:53 pm

Joined: Mon Apr 16, 2012 7:29 pm
Posts: 1658
What is still unclear ?

Top
 Post subject: Re: Inverter LossesPostPosted: Sat Apr 13, 2013 3:39 am

Joined: Sat Apr 13, 2013 3:24 am
Posts: 2
Now with highly oversized arrays and high Vmpp (more modules in series), you have the risk that the overpower correction leads to an operating voltage higher than VmppMax, and in this case the inverter has to stop completely (it cannot find a suitable operating point), leading to high overpower losses.

___________________________
obd2 diagnostic toolgm tech2

Top
 Post subject: Re: Inverter LossesPostPosted: Sat Apr 13, 2013 5:27 pm

Joined: Mon Apr 16, 2012 7:29 pm
Posts: 1658
You are right.
This is explained in detail in the FAQ Why sometimes the oberload losses increase significantly without reason ?

Top
 Display posts from previous: All posts1 day7 days2 weeks1 month3 months6 months1 year Sort by AuthorPost timeSubject AscendingDescending
 Post new topic  Reply to topic Page 1 of 1 [ 9 posts ]

 All times are UTC+02:00

 You cannot post new topics in this forumYou cannot reply to topics in this forumYou cannot edit your posts in this forumYou cannot delete your posts in this forumYou cannot post attachments in this forum

Search for:
 Jump to:  Select a forum ------------------ PVsyst SA Announcements (read only)    Latest news - Bifacial Modelling and 3D Drawing    PVsyst's forum rules FAQ (read only)    Installation and use of PVsyst    Meteo data    PV Components    Shadings and tracking    Simulations : parameters    Simulations : results    Standalone and pumping systems Your questions about PVsyst    Howto    Problems / Bugs    Meteo data    PV Components    Shadings and tracking    Simulations    Suggestions    Tutorials : Feedback and requests Links    PVsyst website    YouTube Channel